Can You Use a Hammer Drill on Wood The Ultimate Guide

It’s possible to use various tools besides a drill press to bore holes in wood, which allows you to keep one hand free. In woodworking, the most popular kind is the (impact drill). Tools like this are light, small, and convenient. When it comes to woodworking, a rotary drill hammer is as antithetical as it gets. However, how about the jackhammer? Can You Use a Hammer Drill on Wood?

If you disable the hammer setting, a hammer drill can be used on wood. However, you’ll waste your time and the drills if you try to drill into the wood while the hammer is switched on.

In this piece, I’ll answer the topic, “Can you use a hammer drill on wood?” in further detail. To determine whether or not a hammer drill, sometimes known as a “jack-of-all-trades,” is suitable for your workshop, you should read this article in its entirety. In addition, you’ll find a comparison of the Drill, the Hammer Drill, and the Rotary Hammer Drill on this page.

What is Hammer Drill

It is common to practice utilizing an impact drill when working with rigid materials. It’s a bit of machinery that can make both drills without causing any damage and drill with a hammering action. The material being drilled is pulverized by the impact mechanism, which does so by repeatedly striking the material with brief hammer blows. Hammering is a third function that the impact mechanism may accomplish without resorting to drilling.

Hammer Drill
Hammer Drill

The clutch of an impact drill is designed to allow for rotation and ramming of the drill into and out of the shaft. The drill’s inward and outward motion length is relatively small, but it is pretty rapid. Between four thousand and five hundred beats per minute are typical.

A single strike produces a little force (between 0 and 4 Joules), but thousands of strikes per minute are enough to break down masonry or concrete. In addition, each blow from the masonry bit’s carbide wedge might crush material in the spiral grooves and send it flying. Because of this, an impact drill can bore through stone or brick far more quickly than a standard drill.

How Many Types of Hammer Drill

The position of the electric motor is another critical differentiator between hammer drills.

The orientation of the drive in some models is flexible, allowing for either a horizontal or vertical orientation.

More force can be generated and delivered thanks to the vertical engine. However, due to their heavy nature, such models may only be used at a rise over the worker’s knees. Heavy hammer drills produce holes of a relatively big diameter (greater than 20 mm) and smash monolithic blocks.

One-hand operation is possible when using lightweight tools powered by a horizontal motor. They aid in the preparation of drywall partition fixing, hole drilling (up to 20 mm), and the creation of wiring accessory niches.

The hammer drill is the tool for DIY projects and industrial settings.

Additionally, there is a weight-based classification system into three groups for user convenience:

Low-Impact Drilling with a Light Hammer —

Power should range between 400 and 800 watts, and weight should not exceed 4 kg. They are indispensable when drilling holes in concrete for dowels, socket boxes, or soldering boxes.

battery-operated hammer drill

Hanging shelves, installing plumbing, and wiring may all be done once the plasterboard profile has been fixed. In addition, tiles may be chipped, and tile adhesive can be removed when in shock mode.

The Use of Medium-Sized Hammer Drills –

One thousand watts is the possible output, and their maximum weight is 8 kg.

Master artisans have these models in their toolbox for use in anything from interior design to carpentry to wiring.

Light hammer drills may do many jobs, but with more power and durability, they can do things like punch through gates to run electrical cable through or remove the old flooring.

Heavy Hammer Drills–

A power output of more than 2000 watts and a weight of more than 8 kg.

Experts rely on these models while doing tasks like deconstruction, refurbishment, communication line installation, and waste disposal.

Hole crowns larger than 100 mm allow you to chip concrete or natural drill stone and create holes in both.

It stands to reason that equipment of this size would be somewhat substantial.

The risk of carpal tunnel syndrome can be reduced by using a tool for extended periods, and manufacturers do this by including dampers in the handles.

How does a hammer drill perform?

Bricks, mortar, and concrete blocks can easily be drilled through with a hammer.

You should give some thought to your hammer drill purchase for a number of reasons..

It is essential to investigate the drill’s capabilities. First, choose a hammer drill that allows you to disable the hammer function so it may be used as a regular rotary drill.

Remember that a hammer drill with many speeds is preferable to one with only one, as it will provide you with more options for different jobs.

You should acquire a hammer drill with a helping handle towards the front for extra support, especially if this is your first time using one, since the drill’s force and strength may be overwhelming.

A more powerful tool is the way to go if you need to drill through rigid material.

When selecting a hammer drill, it is preferable to choose one with a depth setting, also known as a depth stop, to prevent drilling excessively profoundly into the material.

Hammer drill bits are not the same as standard drill bits. Typically, they are carbide-tipped and composed of more robust materials. Bits must be sturdy enough to withstand the pounding of the drill and burst through the concrete or masonry.

The chuck for a hammer drill is also designed differently from the chuck for a standard drill. It is possible to use a regular drill bit in a hammer drill, but the hammering feature will not work. Hammer drill bits last longer and are more resilient than other drill bits.

Choose the power supply for your hammer drill carefully. Hammer drills can be corded or cordless like other portable power equipment. A cordless hammer drill allows you to work regardless of proximity to an electrical socket. In addition, the price of a cordless hammer drill might be lower than that of a corded one if the batteries are included in the package.

However, a corded hammer drill has greater power and can be used immediately; there is no need to charge batteries beforehand. An extension cord is a must when working far from an electrical socket.

You have finally located your hammer drill; the next step is training. You’ll need a pencil, safety glasses, masking tape, a can of compressed air, a hammer drill, and some drill bits.

First, mark the spot on the wall or other surface where you intend to drill. You may use a ruler to make sure your markers are the right height and are consistently spaced apart..

The second step is to wear protective eyewear because of the dust.

Third, adjust the depth stop on your hammer to the desired setting if you purchased one with such a feature. If your hammer lacks a depth stop, you can mark the drill bit with tape to indicate the desired penetration depth.

Fourth, align the drilled tip with the surface mark. Finally, make a 1/4-inch-deep pilot hole by first switching your hammer drill to its slowest, least powerful setting.

The fifth step is to rev it up a little bit.

Sixth, every 15 seconds, pull out your drill bit and clean off the accumulated dirt and dust.

Seventh, when the hole has been made, any leftover dust may be blasted out by blowing compressed air into it.

How to use Hammer Drill

Drilling pilot holes for masonry screws is a common task for professional contractors, and hammer drills are frequently used in this context. The Tapcon brand of anchor-free screws simply threads into the hole. As a result, it’s crucial to drill precise pilot holes, and a hammer drill is the most efficient and effective tool. However, the manufacturer-recommended masonry drill bit is essential for a tight screw grip.

In most cases, metal anchors are set into concrete piers, slabs, or footings in the course of a wood-frame building’s construction. Generally speaking, the hole diameter should be at least 0.5 inches.. An aggregate (gravel) or concrete wall is no match for the speed and force of a hammer drill.

You can easily separate huge rocks and stones using iron wedges and feathers. First, use a hammer drill to make several holes in the boulder. Once you’ve done that, follow up by inserting two iron feathers and a wedge into each hole. If you take your time and alternatively tap each wedge further and deeper into the holes with a tiny sledgehammer, you should be able to split the rock in half.

In addition, a hammer drill is the instrument of choice for drilling into brick or the cement that binds individual bricks together. While drilling into a mortar is simpler, screws and anchors will bite more firmly into brick. True also of drilling into concrete walls.

After disabling the hammer function, a hammer drill may be used as a regular cordless drill/driver for boring holes and fastening various materials.

Can You Use Hammer Drill on Wood 

Now that you understand the various exercises and how they function, you can go on to the last stage of the process. That concludes the primary purpose of this essay, which was to address whether or not a hammer drill could be used on wood.

While the response is undeniably affirmative, there is still something to be said about it that is not inconsequential.

As was previously said, a hammer drill is a versatile tool that can drill holes in various materials, including wood, metal, and concrete. It may even be used to drive screws when fitted with the appropriate bit holder. Similar to a regular drill, a hammer drill has a clutch that may be adjusted for different drilling conditions. For example, it may be adjusted so that fasteners are not over-tightened and damaged.

Hammer drills are the most effective instrument for penetrating wood. However, it’s crucial to remember that it wasn’t initially intended for this task. It is the purpose of a hammer drill to bore through tough materials like concrete.. Always utilize the hammer tool for this purpose.

The hammer feature must be disabled before drilling holes in wood. That has two explanations. First, you would harm the wood and make the hole more comprehensive than it should. For a second, drilling into wood’s pliable texture with the hammer setting would result in the drill “dancing” rather than penetrating. However, whereas a hammer function speeds up the drilling process in concrete, it does the opposite with wood.

Do woodworkers require the use of an impact drill? While I own one (for details, check my review of the Makita HR2470FT rotary hammer on my site), I would have to advise that you shouldn’t. Since you won’t use the hammer function very often, a standard drill suits your needs as a carpenter. However, We suggest a hammer drill if you have to mount several cabinets or if your tasks need you to often drill through concrete or stone. For the same reason, I also own a hammer drill.

YouTube video

Some Guidelines and Suggestions for Hammer Drill

  • Do not use your entire weight to press the drill into the surface.
  • In contrast to power, which affects the hammering action, torque (rotational force) affects the speed (in RPM or BPM). Better decisions about drills can be made with this knowledge.
  • Place a sheet or cloth under the surface of the wall you are drilling through if it is concrete and the room is occupied.
  • Some experts utilize subfloor vacuums to remove debris from the work area.
  • To that end, Bosch offers a wide variety of valuable accessories. There are links below that will take you to some examples of this.
  • Always remember to clean and lube the drill bit.
  • Helpful Hints for Operating a Hammer Drill
  • Wet the material’s surface first to reduce friction and heat during drilling.
  • To do this, some engineers feed water through the drilling machine in a constant stream. The results can be impressive.
  • A decent hammer drill may be evaluated by how quickly it can bore a hole two inches into a concrete block.


Will a hammer drill work on wood?

A hammer drill may be used on wood, but only if the hammering mechanism is disabled. If you turn on the hammer while drilling into wood, you’ll destroy the hole and the wood, and the drill won’t be able to do its job.

Can I use a hammer drill as a regular drill?

Although a hammer drill may be used as a conventional drill by switching to “drill” mode, this mode limits the drill’s capabilities beyond those of a standard drill. Hence both types of tools should be included in any comprehensive toolkit. On the other hand, if you can only afford one drill, make it a hammer drill because it can be used for more things.

Final Word 

Learning to use a hammer drill is simple if you know the fundamentals and how it works. Like learning to drive a car, once you have the fundamentals down, you can quickly move up to larger vehicles like SUVs, buses, and trucks with experience behind the wheel and hands-on training.

Be sure to have your particular model’s handbook on hand as you go through these procedures. You’ll save a tonne of time learning the features and have more faith in the product because it came straight from the maker.

Get out there and enjoy the benefits of using a hammer drill, an excellent example of modern power tool technology.

Leave a Reply

Your email address will not be published. Required fields are marked *