How to Drill Out a Safe Lock- The Ultimate & Secure Guide

Nowadays, it’s not hard to drill through a security lock and retrieve your lost documents, jewels, and other valuables. Yes, but knowing how to drill out a safe lock is necessary.

That’s quite interesting, but may it be too good to be true? Naturally, but if you know your way around a drill, you can take my word for it. Time required is less than you may imagine..

Every once in a while, we’ll misplace the key to our safe or forget the combination. Everyone is feeling the weight of time; I know that. It’s simple to retrieve anything you need from the safe, though. You are using ingenuity with your drill, of course.

Simply clicking on the link will take you to a page where you can buy the finest drill bits available for breaking locks.

Read on for information on how to drill open a safe.. Continue reading because what follows is really useful and intriguing information.

What is the Secret to Unlocking a Safe?

So, I guess it’s not that big of a deal to drill the lock off a safe. But no matter how well you can operate your drill, you shouldn’t think you’re too clever. However, you need to have a firm grasp of a few key details to ensure your assignment’s effective and efficient completion.

You should know that the lock plug will be damaged if you drill a lock, so don’t try to reuse the lock after that. The safe’s mechanism, however, must be in good working order.

So, let’s get started with the steps required to drill open a safe. For your ease, we’ve summarized the entire procedure in manageable bullet points.. This way, you may proceed without any difficulty.

Things to Think About Before Drilling a Lock

Using a Lock Pick

Raking is the greatest place to start when picking a lock if you are unsure of the lock you are working with. Use a pick gun if you can’t feel the lock’s inner mechanisms. It might end up being a time-saver.

Locking It With a Bump

It is possible to bump some types of locks successfully. In the 1970s, a technique called “bumping the lock” was invented to facilitate locksmiths’ removal of locks. A bump key may unlock a lock by inserting it halfway into it and then pounding it with a hammer.

Fixing a Broken Lock with a New One

It is important to have a suitable replacement lock before attempting to drill the original lock.

Obtain Permission From The Property Owner Before Drilling

Since the lock would be damaged if you drill it, getting permission from the owner is essential. Get the point across that you’ve exhausted all other options.

Things to consider before drilling a safe’s lock open:

There are several reasons why the lock on your safe could not work. Before you go ahead and drill the lock off of your safe, you should verify a few things..

Before you go ahead and drill the lock off a safe, make sure you’ve checked these five items first:

  • Perhaps the safe’s bolt is stuck, so you’ll need to apply some lubricant to the lock’s corresponding hole and wait a few minutes before attempting to open it.
  • The safe’s lock cannot be opened since its battery has died. Batteries may often last for at least a year and a half—attempt opening the safe once more after replacing the battery.
  • The activation code may become inactive for a variety of reasons. Ensure you get in touch with the vendor and chat with a representative about the problem.
  • Removing the batteries and unplugging the safe lock allows you to inspect its wiring and ensure everything is linked securely.
  • It’s possible that the safe doors won’t open because their locks contain a delay timer. If you have trouble using the correct combination to open the safe, try again in 15 to 25 minutes.

Materials Required to drill a Safe’s Lock.

Being well-prepared is one of the most vital qualities while trying to get through a challenging scenario. Keep in mind that it will be easier to deal with the situation if you are well prepared and able to keep your cool.

Required to drill a Safe's Lock
Required to drill a Safe’s Lock

Items required to drill the lock open:

  • Using an Electric Drill,
  • Tipped Drilling Tools,
  • Hammers,
  • Tool for tightening screws,
  • Petroleum Synthetic
  • Lubricants,
  • Uses google,
  • Protective Hand Gear,
  • Upgraded Lock for Security.

How to Drill Out a Safe Lock

Even if you’ve never drilled before, a novice shouldn’t be intimidated because it’s not impossible to accomplish on their own. Observe the procedures, and you will succeed. Following these four simple procedures should allow you to drill open any safe.

Choosing Appropriate Drill Bits:

Before beginning drilling, it is crucial to select the appropriate drill bits. If you need to drill out a lock, a 14-inch bit is usually sufficient. However, I have already said that different-sized drill bits should be kept on hand. Lock mechanisms also change across different types of safes.

Choosing Appropriate Drill Bits
Choosing Appropriate Drill Bits

When drilling into a safe with a deep lock mechanism, larger drill bits, such as 1/4 inch, are required for success. You will find success much more quickly if you are properly geared up. The drill bits may be swapped out for more efficient ones. Studying the lock cylinder is another option for determining the appropriate drill bits.

Although 1/8-inch drill bits are adequate for starting, larger diameter bits should be used as time progresses. In addition, drilling efficiency may be improved by periodically cleaning the drill bits.

To clean the debris from your drill bits, have a dry towel handy and use a screwdriver. Steel drill bits are excellent for slicing and sawing through metal; for best results, use high-speed bits.

Start Drilling Right Away:

This is the most important step, so take your time getting started. It’s a really laborious and loud process overall. Please don’t bring your kids or pets.. Put the room in lockdown and put on your protective gear.

Start drilling the lock using 18-inch drill bits. Standard locks often have screws or pins within the mechanism. Understanding where the screws or pins are located is crucial for their removal and destruction. If you begin making holes in the area around the lock, you should be able to locate the screws within.

Simply turning the combination dial will expose the lock’s fasteners. Remove some of the screws using your tool to make them less sturdy. Additionally, the lock’s cylinder may be drilled straight through and penetrated with drill bits to weaken it. There are typically more than 5 or 6 security pins in a standard cylinder lock.

The lock is growing weaker since the pins are damaged from drilling the cylinder hole. The whole thing won’t happen in only 2 minutes. Drilling is a time-consuming process that demands you to be patient. Keep your mind on the task and check to see if the drill bits are growing too hot to handle.

Let the drill cool down, and get some lube before you try again. You must constantly clean the drill’s tip as you operate to maximize its effectiveness.

Remember that you’re just trying to break the lock, not the safe itself. You must maintain a level and straight machine not to harm the safe’s internal components.

Hold the pressure constant and switch out your drill bits:

Drill the safe lock carefully and steadily once you’ve started drilling the lock cylinder. It’s a typical error to put too much pressure on oneself to do the task fast. In addition, the high pressure causes more heat to be produced, making it more difficult for the drill bits to make a clean hole in the lock cylinder.

Drilling the hole might be made easier with the help of a few drops of water, lubricants, or oil. Drilling byproducts may clog the lock. Because of the liquid, you should be able to work it quickly. It has been advised that you begin drilling using 1/8-inch bits. Swap out the drill bits for those measuring 16 or 18 inches to drill the lock’s cylinder.

There are frequently numerous pins in the locks, and you can get through them more quickly if you use pieces of varying sizes to damage them. However, most individuals struggle and become dissatisfied when just one sort of bit is available to them.

The drill bits become stuck when trying to bore out the lock cylinder. Drilling a safe lock requires many drill bits.

Using a set of screwdrivers, unlock the door.

Locks are easily opened if the proper processes are followed, and this is something you will soon discover. First, it’s time for you to use a screwdriver in place of the key and unlock the door. If the screwdriver doesn’t go into the lock, try shifting it to the left or right.

Try tapping the screwdriver with a hammer if you’ve exhausted all other options for unlocking the lock mechanism. Repeat the process if necessary, but this time use other drill bits to get further into the mechanism and perhaps destroy it. After the lock’s framework has been broken, your goods may be retrieved by simply turning the lock.

Jamming might be caused by a buildup of metals and other wastes like trash. To prevent such issues, it is important to use liquids periodically and to clean the drill bits while they are being used.

Regaining access to your safe just requires a few basic skills and the use of certain essential equipment.

YouTube video

Is the security of smart locks improved over that of standard locks?

Either lock has a purpose and can protect your possessions. Nowadays, smart locks are common in homes and offices and can be controlled remotely.

As with their outdoor counterparts, electronic locks are also finding widespread use indoors. Again, you can try this if you are tech-savvy. Sadly, smart locks are vulnerable to being hacked or broken into.

It takes a lot of work to open a conventional lock because of the way they’re made. However, hackers may simply gain access to your smart locks, whereas it takes considerable skill and time for someone with ill intent to open a standard lock.

Nonetheless, you may unquestionably safeguard your home and possessions using security systems and passwords. After you’ve drilled the lock off your safe, you may choose to install any new kind of lock you choose.

Changing it out with a conventional lock that needs a numerical combination to open the safe is the best option if you’re concerned about the safe’s security.

Is a specific drill bit size required to Drill out a safe lock?

Drilling a safe from a lock requires 1/4″ drill bits. Drill bits of various sizes should be kept on hand as the depth of the safe lock holes vary. Drilling the lock holes using 19(mm) bits or 10″ bits will successfully destroy the safe’s pins.

How Much price of a new lock for the safe?

Replacement safe locks might cost anything from $65 to $300. Setting aside $100 to purchase a new lock to replace your old one is safe. A smart or electronic lock will set you back at least $200.

You’ll need to save money for these supplies if you want to crack the safe on your own. Remember that you, too, may one day require these supplies. It’s usually preferable to access these things without leaving the house.

A breakdown of the projected material costs is presented below.

However, if you don’t feel comfortable using a drill on a safe’s lock, a locksmith may do it for you. You may expect to spend between $200 and $500.

FAQs

How do you open a locked safe without a key?

An easy way to pick a lock is to use a screwdriver to spin the key in the lock. Using a flathead screwdriver, open the safe by placing it on a level surface and inserting the tool into the keyhole. Repeatedly turning the screwdriver in a counterclockwise direction should eventually unlock the device. Take out the screwdriver, and the safe will unlock.

What drill bits do locksmiths use?

Whenever you need a drill bit, turn to the Locksmiths Hardplate Tungsten Carbide Tipped Drill Bits. These drill bits come in various sizes and are perfect for use with carbon or stainless steel due to their abrasion resistance.

Conclusion

 It feels great to figure out a new method and successfully implement it. Being resourceful is a boon; it helps you save a lot of money when you apply your imagination. This strategy works on a wide variety of other locks as well..

Adhering to the procedures above can drill out a safe lock without risking injury to yourself or the safe’s contents. Putting in a new lock will restore the safe’s previous functionality.

Self-drilling your lock using the advice in this post should be possible.. If you have any further inquiries regarding lock picking or hole punching equipment, please don’t hesitate to contact me through email.

Leave a Reply

Your email address will not be published. Required fields are marked *